10 11
BELT REPLACEMENT
Warning: Before replacing the belt, make sure the cleaner is unplugged from electrical outlet.
· Turn off the cleaner and unplug from electrical outlet.
· Remove the bottom plate of the base by removing the 5 screws using a Phillips screwdriver.
(Fig. 25)
· Set the new belt over motor pulley. (Fig. 26) Use belt: BLT1.
· Slip the brushroll into the belt and reassemble. (Fig. 27)
· Replace the bottom plate and secure the 5 screws.
Fig. 25 Fig. 26 Fig. 27
HEADLIGHT REPLACEMENT
· Turn off the cleaner and unplug from electrical outlet.
· Press the handle release pedal and use the handle to place the body in a flat position.
· Remove the headlight cover by removing the screw with Phillips screwdriver. (Fig. 28)
· Pull the bulb straight out of the socket. (Fig. 29)
· Install the new bulb, model LBU.
· Replace the headlight cover and secure the screw.
Fig. 28 Fig. 29
Note: Replacement parts can be purchased by calling 1-866-603-5900.
Please check each item below if you have trouble with your cleaner. Before checking, ensure that
the cleaner is unplugged from the power supply.
TROUBLESHOOTING GUIDE
PROBLEM PROBLEM
Cleaner won’t run. 1. Power cord not firmly
plugged into outlet.
2. Motor protector tripped.
3. Need service.
Brushroll won’t spin.
Cleaner or tool won’t
pick up dirt.
SOLUTION
1. Plug unit in firmly.
2. Cool down and press the reset
button. (See page 3)
3. Take to service center or call
1-866-603-5900
1. Cleaner is not in the
upright mode.
2. Brush switch is off.
3. Brushroll is jammed.
4. Belt is broken or off
motor pulley.
1. Incorrect height setting.
2. Hose not attached to
base.
3. Clogged hose.
4. Dirt cup is full.
5. Inner filter is blocked.
6. Crack or hole in hose.
1. Rotate setting knob to correct
height setting. (See page 7)
2. Grasp hose tube and firmly push
onto base.
3. Try to remove clog by squeezing out
of hose.
4. Empty dirt cup (See page 8), if
washed, after dried well, reinsert it.
5. Clean it or replace new. (See page 9)
6. Take to service center or call
1-866-603-5900.
Cleaner is difficult to
push.
1. Incorrect height setting.
2. Brush switch is off.
1. Rotate height setting knob to correct
height setting. (See page 7)
2. Make sure the brush switch is in on.
Visible dust escaping
from cleaner.
1. Dirt cup is full.
2. Filter missing or
installed incorrectly.
3. Dirt cup installed
incorrectly.
1. Empty dirt cup (See page 8) wash it,
after dried well, replace it.
2. Check inner filter & exhaust filter for
correct installation.
3. Pull out and re-insert dirt cup
correctly.
1. The brush only turns on when the
handle is released for vacuuming.
The brush does not come on in
the upright position even if the
switch is on. Depress handle for
brushroll to start turning.
(See page 5)
2. Make sure the brush switch is in on.
3. Remove it and clean debris, hair, etc.
off of brush, then replace.
4. Replace the new belt or correct
belt securing. (See page 10)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals